Cyclic Stick

The Cyclic Stick controls the movement of the helicopter around the pitch and roll axes. Normally you use a joystick for this purpose. The following figure shows a typical real EC 135 Stick with its buttons. Red marked functions are absolutely needed, green are useful when you fly with autopilot. To learn more about assignment of custom functions to a joystick button refer to Setting up Your System. 

  1. ICS RADIO (ATC and intercom)
  2. FTR Force Trim Release button
  3. BEEP TRIM (4way hat switch) 
  4. SAS/AP CUT (turns of SAS and autopilot)
  5. P/R // YAW RST (resets and reactives SAS)
  6. CDS/AUDIO RESET (acknowleges cautions and warning sounds)
  7. APMD DCPL (aborts autopilot's upper modes)
Typical Cyclic Stick

To reduce pilot's workload this rotorcraft is equipped with a comfortable Trim system. It consists of a 4 way BEEP TRIM switch and a FORCE TRIM RELEASE FTR ) button. In real live this is implemented with springs and actors that neutralize pilot's effort in the center of the trimmed position. Is is not possible with normal joysticks to reposition the center position as desired. Therefore we go another way to realize the trim functions. FORCE TRIM RELEASE in EC 135 V5 works as follows:

  1. You are flying as needed to hold the desired flight attitude. Your stick is not centered. 
  2. Press FTR and hold it pressed. Now your stick is decoupled from the helicopter. 
  3. While holding FTR pressed move your stick in its centered position where you have no more effort. 
  4. Release FTR. Trimming is new calculated by the plugin. Your stick gets back the control on your helicopter, but in a more comfortable, forceless position. 
Using Force Trim Release function

For fine tuning the trim position use the BEEP TRIM 4 way switch. 

With Rotor RPM below 80 % pressing FTR button will reset all trimming to zero. So you can get a neutral trim position while standing in IDLE state on the ground. 

Trim functions have other meanings when flying with autopilot. For details refer to AFCS's description. 

See also our video tutorial "Understanding Force Trim Release" to get a deeper comprehension of trim functions.

Force Trim function can be configured to be used with a hardware solution.

Cyclic stick can be locked mechanically or unlocked by clicking on the respective clamp. With locked stick inputs to pitch and roll by joystick are inhibited. 

Clamp to lock stick

Collective Pitch

The Collective Pitch controls the power of the aircraft. When using the throttle lever or a normal joystick it will mostly be necessary to reverse the axis in X-Plane's joystick settings. Standard throttle levers give more power when pressed forward. Helicopter's collective give more power when pulled up. 

On the collective pitch pilot can switch on and off

  1. Search and Landing Light (if installed)
  2. Standard Landing Light
Control Panel at Collective Lever

Yaw Control

To compensate the turning moment of the helicopter you need a yaw control. In the simplest case this can be the twist grip of a joystick. Because it is necessary to control yaw while the complete flight and the helicopter will react very strong to these inputs, we recommend to use rudder pedals for flying helicopters. Best are pedals without as center springs. 

Stability Augmentation System (SAS)

YAW SAS and P&R SAS provide artificial stability in yaw axis respectively pitch and roll axis. Both systems are activated automatically by power-up. Pressing SAS/AP CUT deactivates the SAS. Y RST reactivates YAW SAS, P&R RST reactivates P&R SAS. 

Double Control

A second controller can be connected for a co-pilot or student pilot. With the double control function, the controls can be passed between main controller and additional controler without interruption.

The additional control is connected to the PC as an additional joystick and configured as follows:

  • Pitch axis → REVERSE1
  • Roll Axis → REVERSE2
  • Yaw axis → REVERSE3
  • Collective → REVERSE4

In order to initiate the handover, the command "Switch Pilot/Copilot Control Status" (here SWITCH) is required, which is sensibly configured to a button on the pilot control.

Example of double control gauges. Co-pilot is in control at stick, pedals and collective are ready for take over by co-pilot.

The transfer is started by pressing SWITCH. Gauges appear in the co-pilot's and pilot's NDs, showing the position of the controls. The taker lines up his controls with those of the giver. With that, control is passed. When all axes have been accepted, the gauges disappear automatically. As long as the co-pilot has sole control, the advisory CO IN CMD is displayed at CAD.

Control can be returned by pressing SWITCH again.

Gauge Color Codes: Green is in control. Yellow is ready to take control. Red has no control. Own control position is cyan, each other's control is white.

rotorsim's partners


Outstanding controls for the EC 135. Pedals, Collective and a true-to-the-original stick, even motor-controlled on request. These controls are a must-have for anyone flying the EC 135 in the simulator.


The hardware for the home cockpit. simparts instruments are of exceptional quality. The complete program for an EC135 cockpit is available. And everything is basically plug & play with our EC 135 Pro.


The German Aerospace Center (DLR) is a renowned research institution. Our flight model is used in a simulator at the Institute for Flight Guidance. DLR pilots supported the development.


The ultimate flight experience in an EC 135 full flight simulator. Fully instrumented, motion platform, sensational projection. In Attikon in Switzerland, beginners as well as flight students and professionals get their money's worth.

Heli Simu France

Together with the French developer group HSF we bring the EC 135 for X-Plane into a new dimension. A highly detailed 3D model of HSF is combined with our unique system depth.

HR SimYard

The Austrian developers build high-quality freeware addons for FSX and PrePar3D. Thanks to our partnership, we mutually benefit from each other by exchanging 3D models for the EC 135.